34500.00 $ New Hydmech H-10A, Automatic 10 X 10 Dual Post Horizontal Bandsaw Gordon

Published date: June 25, 2024
  • Location: Gordon, Texas, United States

New Hydmech H-10A, Automatic 10 X 10 Dual Post Horizontal Bandsaw


⭕ HYD-MECH HORIZONTAL BANDSAW

New 2012 Hyd-Mech Automatic Dual Post Horizontal Band Saw

Model H-10A

TECHNICAL SPECIFICATIONS (Description of Machine & Features is below)

Capacity:90º

Rectangular (h x w): 10 x 10

Round: 10

Square: 10

Blade Size: 1-¼ x 126
Blade Drive: 5 Hp
Blade Speed: 50-350 SFM
Band Wheel Diameter: 16
Hydraulic Drive: 1 Hp, 600 PSI
Hydraulic Tank Capacity: 4 US gal.
Coolant Tank Capacity: 15 US gal.
Shuttle Stroke: 0-24 Multi-Indexing
Machine Weight: 3,500 lbs.
Workload: 4,000 lbs.
Dimensions (w x l x h) 83 x 68 x 67
Table Height 31
Wired for 208V

Equipped with:

Variable Vise Pressure: Provides vise pressure adjustment, on both vises, when thin wall tubing and other light material are being cut. Minimizing application deformation potential.



Machine is In Stock. Under Power at our AZ Showroom. Been used as a Demo Machine for our AZ Showroom for the past year or so. Demos Available Upon Request. Available for Immediate Delivery

1 Year Parts & Labor Warranty Included (CA, AZ, NV Delivery Only)

Buyer is Responsible for Freight & Rigging

Price: $34,500.00
FOB: Phoenix, AZ 85040


MACHINE CONSTRUCTION & FEATURES

Machine Base The machine base is designed and produced with electro-welded steel components for maximum rigidity and support. Part of the main construction is a protective cover over the main cutting components, leaving only the vise area exposed. A chip removal auger, leveling bolts and 6.6 US gallon coolant tank are built into the base.

Model H-10A, Dual Post,
New VFD Motor Heavy Duty 5 Hp motor with a A/C inverter provides infinitely variable band speed allowing for efficient cutting of various applications.

H10Shuttle Feed

A roller in feed table and linear bearing mounted shuttle vise assembly provide high speed material indexing of up to 24 in a single movement with length accuracy of .005 per stroke. Driven by a Stepper Motor controlled Ball Screw assembly providing very quick and accurate cut lengths.Hyd-Mech Horizontal Band Saw, Automatic, Model H-10A, Dual Post, New

H10A Split Front Vise

Split Front Vise Provides material clamping on both sides of the blade and resulting in short material remnant length during automatic operation.
Blade Wheels High quality cast iron wheels with heavy-duty wheel & gearbox shaft bearings.
Guide Arms Heavy duty, cast iron guide arms. The idler side guide arm is mechanically connected to the front vise moveable jaw, moving in tandem with the opening and closing of the vise. This provides proper positioning of the guide arm spacing, in relation to material width, at all times.

Blade Guides Replaceable carbide insert guides housed in two heavy duty cast iron guide arms provide cut accuracy of + / - .002 per linear inch of material and excellent vibration dampening.
Powered Blade Brush Driven off the blade drive wheel the 3 blade brush keeps the blade gullets clean, helping to maximize blade performance and life.

Blade Tensioning

Manual Mechanical tensioning assembly allows for quick and simple blade changing. A LED display on the control console provides readout for proper tension setting.
Work Light A halogen work light provides substantial lighting over work piece / cutting area.
Coolant System A pump delivers ample coolant flow through carbide faced and nozzle guides. Flow valves are present for coolant quantity adjustment. A wash down hose with spray gun is also mounted on the machine.

H10A Hydraulic System

Hydraulic System A 3-position directional valve controls vises and head up/down. The hydraulic motor, pump, tank, and manifold are located in a conveniently accessed area.
Positive Down Feed System Provides easy adjustment of both head feed rate and cutting pressure. Feed rate readout is displayed on the machine PLC providing accurate adjustment and setup.
Electrical System The electrical control components are housed in an easy access cabinet in the back of the machine. Components and wiring are labeled for easy troubleshooting.

H10A Evocontroller

Control Panel User friendly and positioned at eye level on the front of the machine. The NC Controller controls the Automatic cycle and allows for Manual operation as well. Job information, such as part length and quantity, is entered through the interface keypad. Up to 999 different jobs can be entered into the PLC memory, and can be called up and performed at any time. Also, a JOB QUEUE function allows up to 100 jobs to be picked from the memory, and run consecutively.The automatic run sequence can be set so that the machine automatically pauses after the first cut between jobs in que in order to allow for a first off inspection prior to proceeding with the rest of the job. A wide variety of languages can be chosen for message screen display.
Manual mode Allows for a fast one cut operation. In this mode all functions are controlled and initialized by the operator. The display shows blade tension, blade speed, blade height position, feed rate, run time of the blade, run time of the cut and blade drive motor amperage draw.

Automatic mode The controller displays blade speed, blade tension part length, feed rate, quantity required, and piece count, job run time, total blade run time. The machine will shut down when the required number of pieces have been cut.

Blade Breakage Switch a function of the PLC software. If the blade breaks during operation the machine will be shut down.

Electrically Driven Chip Auger Built into the base, an auger screw pulls chips from the base and discharges at side of machine.

Blade Deviation Monitor - Monitors lateral blade deviation during cutting. If blade deflection increases beyond the pre-set warning limit, then the monitoring device sends a warning signal by means of a flashing beacon. If no steps are taken to correct this condition, the machine will continue to cut until the pre-set shut-down limit is reached. At this point the machine will behave in one of two ways, selectable by parameter setting:

Stop cutting, raise the head and shut down Or Finish the cut with present degree of deviation and then shut down.

Out of Stock Switch Mounted on the shuttle vise, when the vise closes with no material between its jaws, the machine hydraulics shut down (The cut in progress at the time will finish before shut down occurs). Allowing for the machine to be left unattended with no danger of the machine cycling with no material.


Phone number ✆ +1 469-345-1034

Gordon, Texas

Contact seller Share

Related listings

  • Brand New Ryobi Cordless Tools - Circular Saw And Reciprocating Saw
    TOOLS - Arp (Texas) - July 23, 2024 1.00 $

    Brand New Ryobi Cordless Tools - Circular Saw And Reciprocating Saw ⭕ Two items with your choice [Brand New OR Lightly Used]: 1a) Brand new never used: Circular Saw with Blade - $40 1b) Lightly Used: Circular Saw with Blade - $30 2a) Brand new never ...

  • Welding Cord
    TOOLS - League City (Texas) - July 23, 2024 95.00 $

    Welding Cord ⭕ 100 feet Welding Cord 3/10 Gauge. Phone number ✆ +1 281-874-4173 League City, Texas

  • Shoe Jack Stand For Sale
    TOOLS - Riesel (Texas) - July 23, 2024 300.00 $

    Shoe Jack Stand For Sale ⭕ 3ft shoe Jack Stand, 5 cast iron feet. Rare and hard to find. Readily available for purchase. Phone number ✆ +1 409-611-9402 Riesel, Texas

  • Stihl FS-90 Trimmer
    TOOLS - Alpine (Texas) - July 22, 2024 200.00 $

    Stihl FS-90 Trimmer ⭕ I bought this stihl FS-90 brand new at the end of summer of 2016 from willamette saw shop. i used it about 10 hours total on my yard. i am moving into a bus to travel for the next year and am clearing out my garage. comes with w...

  • DYMO Stainless Steel Labeler
    TOOLS - Mineola (Texas) - July 21, 2024 30.00 $

    DYMO Stainless Steel Labeler ⭕ This is a nice labeler for use with Stainless Steel or Alum. labels. Hardly used at all. $30. Cash call Ron No text, if this ad is up its still available. Phone number ✆ +1 214-234-6867 Mineola, Texas

  • Task Force 3/8 Keyless Chuck Corded VSR Drill
    TOOLS - Mineola (Texas) - July 21, 2024 20.00 $

    Task Force 3/8 Keyless Chuck Corded VSR Drill ⭕ I have a Task Force 3/8 keyless chuck, corded drill that is in like new condition. This variable speed, reversible drill comes equipped with an auxiliary side handle for better handling and work accurac...

  • Air Tools
    TOOLS - Childress (Texas) - July 20, 2024 10.00 $

    Air Tools ⭕ Binks Model 7 spray gun and brad nailer for sale. $10 each. Phone number ✆ +1 430-566-3798 Childress, Texas

  • Tilting Arbor Unisaw
    TOOLS - Indian Lake (Texas) - July 19, 2024 500.00 $

    Tilting Arbor Unisaw ⭕ Delta 10 tilting arbor unisaw with extension table. Very good condition. Comes with assorted saw blades, guides, etc. Price negotiable depending on accessories you want. Phone number ✆ +1 915-982-5836 Indian Lake, Texas

  • New B&D Cordless Powerscissors...
    TOOLS - Groveton (Texas) - July 19, 2024 45.00 $

    New B&D Cordless Powerscissors... ⭕ New Black&Decker Power Electric Scissors Model SZ360 cordless rechargeable...$45... Phone number ✆ +1 281-873-5287 Groveton, Texas

  • Huge TOOL Garage Sale SAT 21st
    TOOLS - Sour Lake (Texas) - July 19, 2024 1.00 $

    Huge TOOL Garage Sale SAT 21st ⭕ Major indoor garage sale with tons of tools! Antique, vintage, some never opened. From our barn to yours..Everything goes home w/you!!! Gas tanks, router, power drills, screwdrivers, wrenches, ramps, chains, sockets, ...

  • Frame Machine For Auto Body
    TOOLS - Toco (Texas) - July 18, 2024 2200.00 $

    Frame Machine For Auto Body ⭕ Up for sale frame machine for auto body , nice working condition GOLD MEDALLION , one support is broken ,as you can see on the picture , very compact and you can move it to any place of the shop , or store it , you do no...

  • Snap On Ratchet Set
    TOOLS - Gresham (Texas) - July 18, 2024 500.00 $

    Snap On Ratchet Set ⭕ Selling my half inch snap on ratchet set for $500 obo. Have used twice so pretty much new. Metric sockets 12mm threw 24mm. set comes with Extensions and breaker bar as u can tell in the pic. Call me or txt me for any questions P...

  • FallTech Full Body Safety Harness
    TOOLS - Albany (Texas) - July 18, 2024 75.00 $

    FallTech Full Body Safety Harness ⭕ Model: Contractor universal fit 7015 With 6 foot lanyard Phone number ✆ +1 512-680-1777 Albany, Texas

Comments

    Leave your comment (spam and offensive messages will be removed)